|
8" ID 45-Degree Blue Silicone Molded Wet Exhaust Elbow with 4 T-Bolt Clamps
Trident silicone-blend rubber marine wet exhaust connections. They are molded in very high-temperature blue silicone EPDM blended rubber with a smooth bore and cover; except elbows of 6" I.D. or larger have molded reinforcing ribs on the outside.
Features:
Four stainless steel t-bolt clamps
Very high temp silicone/EDPM blend rubber - molded
This elbow has excellent resistance to ozone, salt water, diesel fumes, splash, cold, heat, and aging
Exceeds (SAE J2006-R1, and ABYC & NMMA P-1) exhaust standards
Blue very high-temperature silicone blended with EDPM rubber at 350°F (177°C) max continuous
Construction:
Color: Blue
Reinforcement: Reinforcing ribs on 6” I.D. and above
Temperature Range: up to 350°F (177°C)
Specifications:
Inner Diameter: (inch) 8” / 203.2 mm
A: (inch) 2.25” / (mm) 5.7
B: (inch) 2.25” / (mm) 5.7
C: (inch) 8.5” / (mm) 21
R: (inch) 2.12” / (mm) 5.4
W: (inch) 0.37" / (mm) 9.4
Elbow Degree: 45 degrees
|
|
|
6" ID 45-Degree Blue Silicone Molded Wet Exhaust Elbow with 4 T-Bolt Clamps
Trident silicone-blend rubber marine wet exhaust connections. They are molded in very high-temperature blue silicone EPDM blended rubber with a smooth bore and cover; except elbows of 6" I.D. or larger have molded reinforcing ribs on the outside.
Features:
Four stainless steel t-bolt clamps
Very high temp silicone/EDPM blend rubber - molded
This elbow has excellent resistance to ozone, salt water, diesel fumes, splash, cold, heat, and aging
Exceeds (SAE J2006-R1, and ABYC & NMMA P-1) exhaust standards
Blue very high-temperature silicone blended with EDPM rubber at 350°F (177°C) max continuous
Construction:
Color: Blue
Reinforcement: Reinforcing ribs on 6” I.D. and above
Temperature Range: up to 350°F (177°C)
Specifications:
Inner Diameter: (inch) 6” / 152.4 mm
A: (inch) 2” / (mm) 5.1
B: (inch) 2” / (mm) 5.1
C: (inch) 6.5” / (mm) 16.5
R: (inch) 1.75” / (mm) 4.5
W: (inch) 0.25" / (mm) 6.4
Elbow Degree: 45 degrees
|
|
|
6" ID 90-Degree Blue Silicone Molded Wet Exhaust Elbow with 4 T-Bolt Clamps
Trident silicone-blend rubber marine wet exhaust connections. They are molded in very high-temperature blue silicone EPDM blended rubber with a smooth bore and cover; except elbows of 6" I.D. or larger have molded reinforcing ribs on the outside.
Features:
Four stainless steel t-bolt clamps
Very high temp silicone/EDPM blend rubber - molded
This elbow has excellent resistance to ozone, salt water, diesel fumes, splash, cold, heat, and aging
Exceeds (SAE J2006-R1, and ABYC & NMMA P-1) exhaust standards
Blue very high-temperature silicone blended with EDPM rubber at 350°F (177°C) max continuous
Construction:
Color: Blue
Reinforcement: Reinforcing ribs on 6” I.D. and above
Temperature Range: up to 350°F (177°C)
Specifications:
Inner Diameter: (inch) 6” / 152.4 mm
A: (inch) 7” / (mm) 178
B: (inch) 7” / (mm) 178
C: (inch) 2.25” / (mm) 57.2
D: (inch) 2" / (mm) 57.2
R: (inch) 1.75” / (mm) 44.5
W: (inch) 0.25" / (mm) 6.4
Elbow Degree: 90 degrees
|
|
|
3" ID 90-Degree Blue Silicone Molded Wet Exhaust Elbow with 4 T-Bolt Clamps
Trident silicone-blend rubber marine wet exhaust connections. They are molded in very high-temperature blue silicone EPDM blended rubber with a smooth bore and cover.
Features:
Four stainless steel t-bolt clamps
Very high temp silicone/EDPM blend rubber - molded
This elbow has excellent resistance to ozone, salt water, diesel fumes, splash, cold, heat, and aging
Exceeds (SAE J2006-R1, and ABYC & NMMA P-1) exhaust standards
Blue very high-temperature silicone blended with EDPM rubber at 350°F (177°C) max continuous
Construction:
Color: Blue
Temperature Range: up to 350°F (177°C)
Specifications:
Inner Diameter: (inch) 3” / (mm) 76.2
A: (inch) 5.25” / (mm) 133
B: (inch) 5.25” / (mm) 133
C: (inch) 1.75” / (mm) 44.4
D: (inch) 1.50" / (mm) 38.1
R: (inch) 2” / (mm) 50.8
W: (inch) 0.25" / (mm) 6.4
Elbow Degree: 90 degrees
|
|
|
4" ID 90-Degree Blue Silicone Molded Wet Exhaust Elbow with 4 T-Bolt Clamps
Trident silicone-blend rubber marine wet exhaust connections. They are molded in very high-temperature blue silicone EPDM blended rubber with a smooth bore and cover.
Features:
Four stainless steel t-bolt clamps
Very high temp silicone/EDPM blend rubber - molded
This elbow has excellent resistance to ozone, salt water, diesel fumes, splash, cold, heat, and aging
Exceeds (SAE J2006-R1, and ABYC & NMMA P-1) exhaust standards
Blue very high-temperature silicone blended with EDPM rubber at 350°F (177°C) max continuous
Construction:
Color: Blue
Temperature Range: up to 350°F (177°C)
Specifications:
Inner Diameter: (inch) 4” / (mm) 101.6
A: (inch) 5.75” / (mm) 146
B: (inch) 5.75” / (mm) 146
C: (inch) 1.75” / (mm) 44.4
D: (inch) 1.50" / (mm) 38.1
R: (inch) 2” / (mm) 50.8
W: (inch) 0.25" / (mm) 6.4
Elbow Degree: 90 degrees
|
|
|
Blue Silicone Wet Exhaust Hump with 4 T-Bolt Clamps - 8" ID x 8" Length
Trident Silicone Hump Hose Bellows provide the ultimate flexible connectors for marine wet exhaust systems. They offer much greater tolerance to heat, misalignment, engine movement, and vibration, with significant savings in cost, parts, labor, and space.
Construction:
Tube & Cover: VHT blue silicone
Color: Blue
Reinforcement: Polyester reinforcement
Temperature Range: 350°F (177°C)
Specifications:
Inner Diameter: (inch) 8" / (mm) 203.2
Outer Diameter: (inch) 8.5" / (mm) 216
Working Pressure: (Psi) 15 / (Bar) 1
*Burst Pressure is 4 x Working Pressure
|
|
|
Blue Silicone Wet Exhaust Hump with 4 T-Bolt Clamps - 6" ID x 8" Length
Trident Silicone Hump Hose Bellows provide the ultimate flexible connectors for marine wet exhaust systems. They offer much greater tolerance to heat, misalignment, engine movement, and vibration, with significant savings in cost, parts, labor, and space.
Construction:
Tube & Cover: VHT blue silicone
Color: Blue
Reinforcement: Polyester reinforcement
Temperature Range: 350°F (177°C)
Specifications:
Inner Diameter: (inch) 6" / (mm) 152.4
Outer Diameter: (inch) 6.5" / (mm) 165
Working Pressure: (Psi) 15 / (Bar) 1
*Burst Pressure is 4 x Working Pressure
|
|
|
6" ID Blue Silicone Molded Wet Exhaust Hump with 4 T-Bolt Clamp
This silicone and rubber hump hose provides the ultimate flexible connector for marine wet exhaust systems. The hump hose offers much greater tolerance to heat, misalignment, engine movement, and vibration, with significant savings in cost, parts, labor, and space.
Construction:
Tube & Cover: VHT blue silicone
Color: Blue
Reinforcement: EPDM Silicone Rubber
Temperature Range: 350°F (177°C)
Specifications:
Inner Diameter: (inch) 6" / (mm) 152.4
Outer Diameter: (inch) 6.5" / (mm) 165.1
Working Pressure: (Psi) 15 / (Bar) 1
*Burst Pressure is 4 x Working Pressure
|
|
|
8" ID Blue Silicone Molded Wet Exhaust Hump with 4 T-Bolt Clamp
This silicone and rubber hump hose provides the ultimate flexible connector for marine wet exhaust systems. The hump hose offers much greater tolerance to heat, misalignment, engine movement, and vibration, with significant savings in cost, parts, labor, and space.
Construction:
Tube & Cover: VHT blue silicone
Color: Blue
Reinforcement: EPDM Silicone Rubber
Temperature Range: 350°F (177°C)
Specifications:
Inner Diameter: (inch) 8" / (mm) 203
Outer Diameter: (inch) 8.5" / (mm) 215.9
Working Pressure: (Psi) 15 / (Bar) 1
*Burst Pressure is 4 x Working Pressure
|
|
|
4" ID Blue Silicone Molded Wet Exhaust Hump with 4 T-Bolt Clamp
This silicone and rubber hump hose provides the ultimate flexible connector for marine wet exhaust systems. The hump hose offers much greater tolerance to heat, misalignment, engine movement, and vibration, with significant savings in cost, parts, labor, and space.
Construction:
Tube & Cover: VHT blue silicone
Color: Blue
Reinforcement: EPDM Silicone Rubber
Temperature Range: 350°F (177°C)
Specifications:
Inner Diameter: (inch) 4" / (mm) 101.6
Outer Diameter: (inch) 4.5" / (mm) 114.3
Working Pressure: (Psi) 15 / (Bar) 1
*Burst Pressure is 4 x Working Pressure
|
|
|
8" ID x 6' Long Silicone Marine Wet Exhaust & Water Hose - Blue
Trident Silicone Marine Wet Exhaust and Water-Coolant Hose is the ultimate in extra thick soft wall silicone quality with very high-temperature performance and extra long service life. Exceeds SAE J2006-R1, and ABYC & NMMA P-1 exhaust standards. #202V Glossy Blue “Very Hi Temp” has 4-6 ply polyester reinforcement and 350°F (177°C) Max. Used worldwide on premium boats, yachts, and special service vessels. It has become the super yacht standard.
|
|
|
Engine Mount w/6.85" Footprint - 5/8" Stud - 120-410lbs Capacity Per Mount
*** Designed as a rear mount for the Yanmar 4JH series engine
The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull.
To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products.
R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain.
How To Select (details required):
1.Define the total weight of the engine and the transmission.
2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine).
3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine).
4.Determine the stud necessary stud diameter and footprint of the mount.
5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range.
Example:
Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8".
Total weight is 590lbs.
590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010
590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037
Why R&D Marine Engine Mounts?
Designed for marine use, accepts propeller and engine thrust in both directions
Offers a fail safe design
R & D Marine Mounts are height adjustable
Pre-loaded to reduce movement
Slotted holes in base to assist in alignment
Mount types to fit all applications
|
|
|
Engine Mount Kit - 4 Engine Mounts f/Small Yanmar Engines (Yanmar*)
* Suitable for the Yanmar 1GM, 2GM, 3GM, 3YM, 3HM and 3JH series engines
The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull.
To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products.
R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain.
How To Select (details required):
1.Define the total weight of the engine and the transmission.
2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine).
3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine).
4.Determine the stud necessary stud diameter and footprint of the mount.
5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range.
Example:
Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8".
Total weight is 590lbs.
590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010
590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037
Why R&D Marine Engine Mounts?
Designed for marine use, accepts propeller and engine thrust in both directions
Offers a fail safe design
R & D Marine Mounts are height adjustable
Pre-loaded to reduce movement
Slotted holes in base to assist in alignment
Mount types to fit all applications
|
|
|
MF 844 Vented Loop - 1"
Installing one of our vented loops will ensure that fluids will not siphon from tank to tank. Vented loops are commonly used in the marine toilet system and engine cooling system. The simple valve system incorporated in the top of the loop allows air to enter the line when not in use, yet effectively seals as water or other fluid passes through. Molded in Marelon, neither vent nor loop will corrode. The duckbill one way valve is designed to seal properly if particulate matter is present in fluids.
Specifications:
Barb Size: 1" (25.4mm)
Height: 7" (177.8mm)
Width: 9" (228.6mm)
|
|
|
MF 839 Vented Loop - 1-1/4"
Installing one of our vented loops will ensure that fluids will not siphon from tank to tank. Vented loops are commonly used in the marine toilet system and engine cooling system. The simple valve system incorporated in the top of the loop allows air to enter the line when not in use, yet effectively seals as water or other fluid passes through. Molded in Marelon, neither vent nor loop will corrode. The duckbill one way valve is designed to seal properly if particulate matter is present in fluids.
Specifications:
Barb Size: 1-1/4" (28.57mm)
Height: 7" (177.8mm)
Width: 9" (228.6mm)
|
|